Canon BJ/HY078 Instrukcja Użytkownika

BJ-200eUSERMANUALCanon

If your printer was damaged in shipping, or if any items are missing, notify your dealer immediately.As you unpack the printer, save the carton and pa

Choosing a Location for Your PrinterWhether at home or in the office, you need to find a comfortable and convenient location for the printer. Follow

Keep the printer and your computer away from potential sources of electromagnetic interference such as loudspeakers or the base units of cordless tele

Examining the PrinterBefore setting up your printer, you should become familiar with its components and understand their functions. From the FrontPap

Aligns paper in the sheet feeder. You can adjust the guide for paper widths of up to 9 1/2 inches (240 mm).Paper restKeeps the paper straight in the s

AC power receptacleAllows you to attach the printer's power cord.Parallel interface portAllows you to attach the printer's interface cable.

Assembling the PrinterNow that you are familiar with the components of your printer, you are ready to install the printer and connect it to your comp

To install the ink cartridge, follow these steps:1. Grasp the sides of the front cover and open it so you can access the cartridge holder.2. Take the

4. Locate the cartridge holder on the right side of the printer. 5. Lift the green lock lever on the cartridge holder.CAUTION: Avoid touching the yell

6. Fit the ink cartridge over the yellow mounting base with the print head facing down. (When installed correctly, the label on the cartridge will app

ContentsChapter 1IntroductionFeatures and BenefitsUsing This ManualCustomer SupportServicing the PrinterChapter 2Setting Up the PrinterUnpacking the P

Chapter 3Loading PaperThis chapter describes how to load paper, envelopes, thick paper, and transparencies in the printer. To ensure the best performa

3. Fan the paper before stacking it in the sheet feeder. Always fan a stack of paper along the edge that will feed into the printer first. NOTE: Set t

4. Align the stack of paper with the right edge of the sheet feeder and slide in the stack until it stops. Do not force the paper into the printer. Ma

7. Make sure the printer is on-line and start your print operation. Printing On EnvelopesYou can stack up to 15 envelopes in the sheet feeder. Before

When you are ready to load envelopes, follow these steps: 1. Make sure the printer is turned on and on-line.2. Turn on the envelope mode by pressing a

5. Arrange the stack of envelopes on a firm surface and press down firmly on the edges to make the folds crisp. Press all the way around the envelopes

7. Adjust the paper guide to the stack of envelopes.

8. Start your print operation. Turning Off Envelope ModeAfter printing on envelopes, follow these steps before printing on normal paper again:1. Set

1. Make sure the printer is turned on and on-line.2. Set the paper selection lever (on the right side of the sheet feeder) to the for ward position.3.

5. Slide in the sheet until it stops, and hold it for about two seconds. The printer will automatically load the paper into position.6. Start your pri

Chapter 1IntroductionCongratulations on your purchase of the Canon Bubble Jet Printer BJ-200e. We appreciate your choosing this printer to meet your p

Chapter 4Using the Operator PanelYou can control basic printer operations through the operator panel. The indicator lights reflect the current status

receive data from your computer. At this time, you can send print data from your computer to the printer.If you want to pause a print operation, press

Select your print mode as follows: Use HQ mode for most of your printing needs. The printer automatically prints in HQ mode unless you change the mode

When using reduction mode, you must select the correct paper size within your application. In the example above, you would specify a paper size of 11.

When using reduction mode, you must select the correct paper size within your application. In the example above, you would specify a paper size of 15

To print the test prints, you must be automatically feeding a stack of paper. The test prints are not available when you are manually feeding paper.Se

In Epson LQ mode, the self test looks like this:Font ListYou can print this sample in both printer control modes: BJ-10 mode or Epson LQ mode. The pri

To stop printing the font list, press and hold the ON LINE button for one second. The printer stops printing, ejects the current sheet of paper, and g

Demo PrintYou can print this sample in both printer control modes: BJ-10 mode or Epson LQ mode. The demo print describes a few of the printer's

You only need to set this function if you are using an application program that does not include a carriage return with a line feed.To set the automat

wide variety of applications: BJ-10 mode emulates the IBM Proprinter X24E printer Epson LQ mode emulates the Epson LQ-510 printer Two print modes/spee

CHAPTER 5USING THE PRINTER WITH YOUR SOFTWAREYour printer will work with a variety of applications, such as spreadsheet, word processing, and graphics

1. Turn on your computer.2. Make backup copies of the Windows Driver and On-Line Guide diskettes.3. If you are not already in Windows, start Windows b

From this screen, you can select the paper size, media type, paper source, print selection, print quality, and orientation. Click on the drop-down arr

Select Plain Paper when you are printing on ordinary bond paper. Select Transparency when you are printing on transparency stock. (You must manually f

OptionsAs part of your printer setup, you can specify certain options that control the half-toning and intensity of your printed graphics and text.Fro

Printing a DocumentThis procedure provides general steps for printing from the various applications you may run in the Windows environment. The exact

on OK to exit the TrueType dialog box.12. Click on Close to exit the Fonts dialog box. Your installation is now complete.If you would like to remove t

press Enter.10. At the printer Helps and Hints menu, press F7.11. At the printer Edit menu, press F7.12. At the Select Printer menu, the BJ-200e drive

Canon BJ-200eCanon BJ-200Canon BJ-230Canon BJ-10e/BJ-10ex/BJ-20IBM Proprinter X24E/XL24IBM Proprinter X24/XL24ECanon BJ-130eIBM ProprinterTo use the p

The following table lists the fonts and pitches that are available in each printer control mode.* In BJ-10 mode, Courier 12 cpi is available in HS mod

If you set up the printer using the Quick Start Guide, you can read this manual for more detailed information on how to operate the printer.Once you a

You use DIP switch 11 to select the printer control mode. When DIP switch 11 is OFF, which is the default, the printer uses BJ-10 mode. Set DIP switch

CHAPTER 6MAINTAINING THE PRINTERThis chapter covers the care and maintenance of your Canon Bubble Jet Printer BJ-200e. This includes guidelines, clean

Be very careful when cleaning the printer. Follow these steps:1. Clean the inside of the printer using compressed air pressure or a soft cloth to remo

You have been using the cartridge for using the cartridge for over one year.Your printed output is not crisp and clear, or there are gaps in the chara

To avoid spilling ink, follow these precautions: Do not touch the print head on the ink cartridge or the sharp edges around it.Do not hold the ink car

4. Take the new ink cartridge out of its protective packaging. Slide off the orange protective cap from the print head and then remove the orange tape

6. Push the lock lever down until it snaps into place. Make sure there is no resistance when you press on the lock lever, and be sure no gap exists be

7. Close the front cover. When you are not using the printer, make sure the ink cartridge is in its home position, which is on the right side of the p

Storing Ink CartridgesFollow these guidelines when storing your ink cartridges: Keep a new ink cartridge in its sealed container until you are ready

5. Close the front cover.6. Return the paper rest and paper exit support to their original positions.7. Repack the printer in its original packing mat

The Canon Bubble Jet Printer BJ-200e Programmer's Manual is available for software designers, advanced programmers, and users interested in using

CHAPTER 7TROUBLESHOOTINGThis chapter contains information to help you solve printer problems. A problem may have one or a combination of causes, inclu

If you have a problem with your printer and you cannot resolve it by referring to the information in this chapter, contact the Canon help desk at 1-80

1. Make sure the power cord is plugged securely into the AC power receptacle on the back of the printer. 2. Make sure the power cord is plugged secure

If you turn on the printer and the ON LINE, HS, and HQ indicators are blinking, a RAM/ROM error has probably occurred. Try these steps to clear the pr

1. Make sure the paper is not sticking together. Fan the stack of paper before placing in in the sheet feeder. Always fan a stack of paper along the e

Envelopes Do Not Load1. Set the paper selection lever to the front position.2. Make sure the envelope is loaded properly: The flap is toward the sheet

Paper Does Not Eject After PrintingMost software applications tell the printer to eject the paper after printing, however, some do not. If the printer

Print Density is LowThe print density in HQ mode is higher than HS mode. If you are using HS mode and not getting satisfactory darkness, try HQ mode.P

printed output, clean the print head as described in the next section.Print Head Needs CleaningPaper dust or ink may get clogged in an ink nozzle in t

Printing ProblemsThis section contains problems and solutions related to your printer or the software you are using.Printout is WrongIf strange charac

A.M. to 5 P.M. Eastern Standard Time (EST), except on holidays.If you seem to have an operational problem, try to solve it by referring to the informa

For envelopes, set it to OFF.For A4-size paper, set it to ON Printout Does Not Match Paper Size1. Make sure the paper size you select within your prin

CHAPTER 8CUSTOMIZING THE PRINTERThis chapter describes the factory default settings of the printer and the steps you follow to customize these setting

DIP Switch SettingsThe DIP switch settings control various printer functions, such as the page length and character set you want to use. The printer

DIP Switch FunctionsDIP switch 1Use this switch to change the horizontal print position according to the size of your paper. If you are using letter-s

switch is ON; the printer uses Character Set 2.DIP switches 5, 6, 7These switches allow you to select the following code page tables.To see the sample

When DIP switch 12 is OFF, the printer control mode is set by DIP switch 11 (OFF selects BJ-10 mode, ON selects Epson LQ mode).Automatic emulation mod

DIP switch 1Use this switch to change the horizontal print position according to the size of your paper. If you are using letter-size paper or COM 10

DIP switches 8, 9, 10These switches allow you to select one of eight font typefaces.DIP switch 11When this switch is OFF, the printer is in BJ-10 mode

To change a DIP switch setting, follow these steps: 1. Make sure the printer is turned off.2. Open the DIP switch cover on the top of the printer. Pul

Appendix APrinter SpecificationsThis appendix lists the specifications of your printer.Printing MethodBubble jet ink on-demandPaper HandlingAutomatic

warranty program beyond the two-year warranty; however, some authorized Canon dealers may offer such programs for a fee. If you are interested in an e

Envelopes:Horizontala 8.3 to 8.5 inches (210 to 216 mm)b 0.25 inch (6.4 mm) -- Letter-size paper3.4 mm (0.13 mm) -- A4-size paperVerticalc 11 to 14 in

Reduction ModeU.S. Paper sizes:Commercial number 10 DL-sizeHorizontala 9.5 inches 220 mmb 0.25 inch 6.4 mmc 1.2 inches 10.4 mmVerticald 4.1 inches 110

European paper sizes:

Printing DirectionBi-directional in text (both in MS-DOS and Windows)Unidirectional in graphicsPrinting WidthMaximum 8 inches (200 mm)Line Feed Speed1

Maximum Number of Characters per LineBJ-10 modeEpson LQ modeCell Composition:36 (h) x 48 (v) dot matrix in HQ mode18 out of 36 (h) x 48 (v) dot matrix

Acoustic Noise Level Per ISO 7779Approx. 42 dB(A)Graphic Image PrintData format: Vertical 8, 24, and/or 48-dot formatResolution: Horizontal 60, 120, 1

Power SourceUSA/Canada AC 120V, 60HzUK/Australia AC 240V, 50HzEurope AC 230V, 50HzPower Consumption7 watts maximum nonprinting23 watts average printin

Chapter 2Setting Up the PrinterThis chapter describes the steps you follow to unpack and set up your printer. It offers guidelines for finding a suita